2010 Mazda B2000 A-TACS Camo Ballistic Seat Covers

50/50, 60/40, 40/20/40, Solid Bench, Backrest, Bottom

These refer to the most basic configuration of your vehicle's seats. The illustrations below are common configurations. There can be combinations of the above, such as 60/40 seat backs with solid bottoms.

Power driver, manual driver, power passenger, manual passenger

Power driver and power passenger refer to seats with knobs to electronically adjust the seats back and forth.

Manual driver and manual passenger refer to seats where you must physically move the seats to make adjustments.

Fold-Flat Passenger Seat, Folding Pass Seat

Some vehicles have a passenger seat that will fold flat. The seat must fold forward all the way flat, like a table.

Removable Headrests

Headrests can be removeable/adjustable, where they telescope up and down. In these cases there would be separate headrest covers included (the headrest must be removed to install the seat back cover).

Headrest covers will not accommodate DVD/TV screens unless specifically stated in the description.

DVD Headrest Screens

Headrest covers will accommodate DVD/TV screens only if specifically stated in the description. If you have a DVD screen in a removeable headrest, you will need to disconnect any wires that travel between the headrest and the seat back in order to get the seat back covers on.

Built-in Headrests, Molded Headrests

Headrests can be built-in or molded into the seat back. These do not need separate headrest covers. The seat backrest cover accommodates the modled headrest.

Recessed Headrests

Recessed headrests sink into the seat backrest somewhat. They are common with sport seats.

Non-Recessed Headrests

Non-Recessed headrests sit flush on top of the seat backrest.

Side Airbags

If your vehicle's front seats have side airbags, your seat covers must have airbag allowances (flaps) for the airbag to deploy safely and properly. The existance of side airbags on your car seats is usually indicated by a small tag or imprint saying "Side Airbag" or "SRS" on the door side of your seat backs. If your seats have side airbags, please make sure our description of the seat covers you choose indicates side airbags ("w/side airbag"). Please contact us if this is not the case.

Console, Top Console

Consoles are almost always in the middle of the seat row and often open to store items. Folding consoles fold up to become a seat back and fold down to become an armrest, sometimes with cupholders. Console covers are included when they are in the seat cover description. Standalone consoles that are not part of the seat (commonly with 50/50 bucket seats) do not have covers.

Center bottom storage/bottom console

40/20/40 seats with a bottom console have a middle seat bottom (where you sit) that lifts open for storage.

Built-In Seat Belts/Integrated Seat Belts

Vehicles with integrated or built-in seat belts have a shoulder belt that attaches to the top of the seat, rather than the side of the vehicle frame.

Lumbar

Seats with adjustable lumbar have a lever that moves the support in the bottom of the seat back. There are manual lumbar controls (usually a lever) and power lumbar controls (usually a knob or button that moves the support electronically).

Flap Liner

On some seats, there is a flap on the back of the seat that attaches the seat back to the seat bottom. This flap prevents the seat cover from being installed, you will have to lift the flap up in order to install the seat cover. This will be notated in the description and instructions on doing this will be provided.

Requires Professional Installation

Some rear seat covers will require the seat to be physically removed to place the cover on properly. In these cases, professional installation is recommended/required for safety reasons. These seats covers will be notated as requiring professional installation.

All custom covers and floor mats are special order and require time to make before shipping. Production times can vary, depending on many factors.

Expected timeframes are provided below, and these are updated every week.

Total production times below (from order to shipping) are up-to-date. Last updated 11/12/24

• Custom Car Covers - Approx. 1-2 weeks
• Custom Seat Covers - Approx. 1-3 weeks (Saddleblanket dark blue delayed. Printed camo are currently taking longer.)
• Custom Dash Covers - Approx. 1-3 weeks
• Custom Molded Dash Covers - Approx. 1-3 weeks
• Custom Floor Mats - Approx. 1-3 weeks

Production times cannot be guaranteed during this time. Thank you for your understanding.